The Original Grip Puppy Comfort Grips

My original (BMW) heated grips were showing their age. WIth big hands, they were also somewhat uncomfortable on long rides. Highly regarded by fellow owners, and I agree 100%. The added diameter and soft but textured material are perfect.Installation is easy, just a little dilute soap solution sprayed while sliding them over the original grips. I was concerned that they would slip and rotate, but the next day (after the water evaporated) they are solid. Heated grip function is fine, takes just a bit longer to transfer through, no issues.

These grip work very well, easy to install, comfortable, cuts down vibration and is good for arthritis in the hands. Just a little soap on the inside and slip them over your old grips, couldn’t get much easier than that. I had to cut down the throttle side though. Just slip a socket inside the grip to where you want to cut it and use a razor blade and cut right next to the socket and you’ll have a nice clean straight cut

Great upgrade for $20. My stock scooter grips were crappy, soft gloves could grip them but my more protective hard leather gloves didn't grip well, causing hand fatigue on a half-hour commute. The texture of the grip puppies makes a huge difference, now I can simply roll my palm on the throttle for effortless control, without needing to squeeze with my fingers. The larger diameter is an improvement as well, for comfort and control.One thing to note: you may need to trim them to make sure you're not getting accidental cruise control. The puppies are just slightly longer than my throttle handle, so it was gripping the knob at the end of my bar and holding the throttle open. Had to take off a quarter inch, but even with that, install took only a few minutes. Couple drops of water-based lubricant and they slid right on. 5/5 product

I got these for my 08 Suzuki Hayabusa.My reasoning was that when I rode I would get pressure and red sores on the lower side of my palms after more than 30 minutes of riding. This is obviously uncomfortable and takes the fun out of longer rides.I installed these by putting some soapy water inside the middle, didn't have to soak them, and slid them on after 5 minutes of work each side. Installation is no issue.The GOOD: So they do work, it took a good amount of pressure off my palms and I didn't get the sores anymore and did a 400 mile trip.The BAD:these make the handle bars very thick. I have medium sized hands and it eventually caused more strain on my wrists holding onto this bulky padding. The throttle does not feel as responsive and fine when it's this big hurking handle.IN THE END: I realized it is not because the handles are too hard that I was getting these sores. It was due to the angle of sitting that put all my bodies weight resting on the handle bars WHICH IS NOT HOW IT SHOULD WORK.So I took them off, I bought some Heli-bar risers which are a little pricy around 150. They raised the bars up by maybe 1/2-1 inch and towards me more by half an inch.This COMPLETELY fixed the issue. No longer pushing against my handlebars, no hard spots on my palms and a completely different riding experience. I've put another 2000 miles with the stock grips and the heli-bars and have absolutely no issues.I would also recommend getting a good seat like Corbin, Sargent, mustang or other. These usually will be lower than stock and take more pressure off your palms as well.If you're having issues and pain on your palms/wrists while riding I suggest you fix the actual problem instead of adding more padding. My riding experience is just as good with the heli bars and I didn't have to compromise.

Super comfortable and fit great. I hear a lot of customer issues happening during install and not sure if they are using soapy water on the handlebars before trying to slide them on but it made it very easy for me and no signs of tearing. I mean you still have to twist them back and forth or rotate them around in a circular motion to work them on but in total on two motorcycles it took me 10 minutes. And then I just trimmed off the excess.

The media could not be loaded. I wasn't too sure, A little skeptical about them, until I got them and installed. No need for new grips with this amazing product. I am totally pleased at the fit and the comfort of these Grip Puppy hand grips on my Honda CRF 300 rally.

These things are great. The increase in grip diameter relieves hand strain, and the foam is the perfect stiffness for comfort. They also prevent your hands from slipping when the rains come. These stay stationary on the grips while riding whether it rains or shines. Just a little Dawn soap and some water is all it takes to install them. (I cut mine to the perfect length before sliding them on)My concern was the impact they would have on heated grips, but they pass heat through just fine. They may slow down the heat transfer rate some, but they will still let your hands get quite toasty if your grips have the power to get hot.For this price, if you're not happy with them cut them off and throw them out, but once you try them I'll bet you leave them on.

I have XL hands and the standard grips were too small diameter to be comfortable. Besides allowing my hands to be more comfortable these also reduced the vibration.