Nano Polymer Adhesive (50ml) - Ultimate 3D Printing Bed & Build Plate Adhesion - No Mess, Non-Toxic, Works for PLA, ABS, PEI, PEEK, Nylon, PC and More. Easy Application, Easy to Clean!

I’ve tried several plate adhesives, including Bambu Lab’s Liqui Glue, Magigoo, and standard glue sticks, but Vision Miner Nano Polymer is by far the best I’ve ever used. It’s extremely easy to apply and lasts a long time.I was having trouble with PETG sticking to one of my G10 build plates. After applying Nano Polymer, the PETG stuck perfectly during printing, and once the plate cooled down, the parts popped right off without any issue. Even after printing multiple parts in the same spot, adhesion remained strong.This has become my go-to adhesive anytime I run into adhesion problems. I primarily print with PLA and PETG, so I haven’t tested it with more exotic filaments, but based on my experience, I’d highly recommend it and I’d be confident it works well with other materials too.The only issue I had initially was applying too little adhesive. After watching their instructional video, I realized I wasn’t using enough. Now I follow their method: draw an “X”, circle it, and brush it in two directions. Since then, it’s worked amazingly well.

Absolutely amazing glue. I like to work with lots of different materials quite frequently. From PLA to PETG, ABS, ASA, Polycarbonate, Nylon, PPS, and several Carbon Fiber composites. I wanted a glue with strong reliable adhesion, and after looking at certain options such as magigoo, I found it a bit annoying to have to use and purchase various formulations of glue for all the different materials I use, and wished there was an "All in one" glue that just works with everything. I then discovered this stuff after watching some videos from Visionminer on YouTube and it sounded exactly like the glue I was looking for. Ordered some and let me tell you, it works with EVERYTHING I mentioned earlier and more. Super simple to apply with the included applicator brush, dries in seconds, hit print, and walk away knowing that I won't have any issues with bed adhesion. Only thing it doesn't work with is polypropylene, but that stuff has trouble sticking no matter what method of adhesion you use. Other than that, EVERY. SINGLE. FILAMENT. has worked for me with this glue and I cannot recommend it enough. The price is more than worth it for the peace of mind alone, and it will last you a good while as well since one application tends to last for several prints. 10/10

I know this stuff is overpriced. But it really works well and is reliable when I know I have a tricky filament to print. It does seem to have some IPA in it so if your build plate doesn’t play nice with IPA I’d consider something else. Otherwise I depend on this adhesive. I just squirt some on the plate and wipe it around my printing area with a paper towel. Done.

This works great. Great adhesion, and release once cooled.

I've been printing for about 6 years and I've had a half dozen printers. I'm very experienced and knoweldagble about the variables that contribute to bed adhesion.My newest printer was having some trouble with very small contact surface adhesion and I couldn't use a raft or brim due to the nature of the print and post processing. I'd cleaned the bed with soap, water, rubbing alcohol. Still had trouble with adhesion, unable to get all parts to stick.Bought this stuff, painted it on, ran the same print I'd had 3 previous failures on. Worked perfectly. Decided to step it up and run 12 copies instead of 3... worked perfectly. Did it once more, 12 copies, again flawless. Where previously 1 or 2 out of 3 was having adhesion trouble, the last 27 copies have been flawless without a single failure.That said, I'm sold. I'll keep using this until I find a reason not to. I don't know how long a coating lasts but I've only done one so far so I imagine the 50ml I purchased will last quite long. Highly recomme d

Let me tell you, the Vision Miner Nano Polymer 3D Glue has completely blown me away. I've wrestled with my fair share of adhesives over the years in this hobby, and honestly, this stuff is in a league of its own. The adhesion it provides is just phenomenal – prints stick firmly to the bed without any annoying warping or lifting, even with tricky materials.But it's not just about the stick; the release is equally impressive. Once the bed cools, parts practically detach themselves, leaving a clean surface behind. No more scraping and potentially damaging prints!The application is smooth and even, and a little goes a long way, which means this bottle is going to last. Honestly, the reliability and ease of use this glue provides have made my 3D printing experience so much more enjoyable and stress-free.Consider me a convert. From this point forward, Vision Miner Nano Polymer 3D Glue is the only adhesive I'll be reaching for. It's simply the best I've ever used.

This stuff works great dries quickly and last a while