Omada SG2005P-PD | 5 Port Outdoor PoE Passthrough Gigabit Ethernet Switch | 1 PoE++ in@90W, 4 PoE+ Out Up to 64W | IP55, Static Routing, Access Control List, QoS, VLAN | PoE Powered ONLY

I bought two of these SG2005P-PD to connect cameras and Wi-Fi in my yard. They were easy to set up using the SDN Omada app and my OC200. You don't have to use the controller to make it work, it connects right out of box. Only drawback is that you have to provide a PoE injector. I'm using a 90w injector. In retrospect, a 60w would have been enough, but that's OK because I can power another PoE pass through switch with the extra wattage I have available. I like that I can monitor the devices connected to the switch and it even supports PoE recovery. All in all, I would say it worth the money spent.

A solid performing switch and it can be managed remotely through Omada. I have this mounted in the rafters of my garage using the included bracket. It powers and AP and a couple of hardwired devices. The included POE injector is a little anemic but it works for my use case. It works as advertised and I’m happy with it.

I bought this because it supports both VLANs and PoE pass-through. I'm powering this using PoE from another room in the house and this, in turn, powers three Unifi access points using PoE without any problems. I need VLAN segmentation, which this version supports. This switch can be managed centrally using their software, but I chose to instead manage it from its built-in web interface. I was pleasantly surprised by both the number of features exposed as well as the ease of configuring these; it was all very intuitive (if you're familiar with VLANs, in general). I'm also happy to report that it can be configured to route both IPv4 and IPv6. The case itself is also pretty good for an outdoor installation as it has protection that goes over the Ethernet ports, though I chose to install mine inside. I would have gone with an 'indoor' version of this if I could find one with the same capabilities for around the same price.

Since the products are combined on one product page this is two reviews. First, for the outdoor unit: 1. This does not have any way to power itself. That means your need to find an outdoor powering solution... which defeats the point of buying this for its outdoor feature in the first place in most scenarios. 2. Its overpriced. There are a few outdoor poe switch options on amazon that cost less and actually do come with power. So half the work required and you didn't pay as much. 3. The holes for the ethernet to go through aren't exactly waterproof. And they're also not lined up with the ethernet ports, which means there will be a severe bend between the switch and the cover. With the bend, a larger ethernet cable cant really make the bend. With my thicker ethernet cables I have to leave the cover off which means it's not much different than a non outdoor unit. 4. Also, be sure to note you CANNOT use a passive Poe injector to power this. You have to buy a $75 poe injector to get this working. And then you have to find a way to make that injector usable outdoors. In my setup that was another $50 outdoor box... at which point, why not just put a non outdoor switch in the box instead? Second, the desktop switch lasted about 6 months. The previous one I had was about the same. I want to love tp-link because I use their business stuff, but the truth is, the products are just average.

Great little switch, works well for both indoor and outdoor environments. It has PoE passthrough which means it's both powered by PoE in and can also provide PoE to downstream devices. I've got one in my garage and the fact that it's PoE powered meant that I didn't have to run new electrical wiring for it (it's in a location that doesn't have any power outlets). I've got two security cameras plugged in to it, both powered by PoE, and it's working well. Total power usage for my use case is a little less than 10W total. The switch itself is using around 4W. I've also got one non-PoE device plugged in to it. It supports management with an Omada Controller, or you can manage it standalone by going to its IP address in a web browser.

Needed a switch for my patio that could handle being exposed to the elements and didn’t need an electric socket near by. This fits the bill perfectly and since I’m already heavily invested in the Omada ecosystem, it fits in perfectly. My only wish is that they would just bump the price up a bit and chuck a POE++ injector in the box. I had to buy one separately since my switch doesn’t support POE++ and all my spare injectors are POE+. Anywho, this thing appears to work perfectly. It was painless for my Omada controller to adopt it and update the firmware. This is a very nice little switch. For my uses this will power two POE cameras, a POE access point and will provide a wired data connection to an outdoor smart TV.

I'm not certain if it's the switch, or the POE injector I chose to go with it (TP-Link TL-PoE170S), but after power outages, the unit will not reboot with devices attached to it. It shows no status lights until I remove all the cables, and then insert the POE source cable. It will then boot up, and I can plug in in the two POE cameras that it supports. Logging into the switch, I can see the cameras only use about 8w total, so I'm nowhere near the budget for either the switch, or the injector. Fortunately, the switch is at ground level, but we do have a fair number of outages, and this is a hassle.

I bought two of these to wire my external security cameras. I have them connected to the POE ports on my TP-Link Omada SDN POE switch. I love how the status of each port is visible on the unit. It helps with troubleshooting issues. I can manage the switches using Omada Controller that I have self-hosted on a VM. I can see what my maximum power draw is, how much I have left, how much power each port draws, and I can restrict/assign VLANs. I want to get more to propagate throughout my property.

Una gran ventaja es que sólo necesita alimentarse de un sólo cable de red tanto para datos como para energía. Bastante útil si quieres conectar más dispositivos por LAN, y te ahorras metros cable, en vez de jalar cables desde el Switch principal.