Loud Speaker Repair Glue Foam Side Dust Cap Rubber Edge Cone Basin Strong Adhesive 50ML/1.68 fl.oz (1)

I used this to repair/re-foam 6 speakers since I purchased it. The first set was a pair of old Advent bookshelf speakers, I used them for a while before using the glue on 2 pair of vintage Polk audio speakers. Once I sourced the foam, I removed and cleaned the surface area and followed the directions for speaker re-foam I found online. I use the small set of Polk bookshelf speakers daily for months and they are holding up well. The other set of speakers were 1987 Polk Audio Monitor 10b's that needed foam on the woofers and passive subs. I followed the same process as before and they work great. It's been about a year with no problems. I give these speakers the beans regularly as part of my vintage audio system and 250w amp. They're holding strong so, I'd say this glue is quite good.

Used them to re-foam a pair of old Realistic 77 speakers. Started to hold in about 1/2 hour and full cure in 24 hours. Very easy to use. The glue flowed easily and the cap with a pin sealed the tube for later use.

Used to repair an antique radio speaker that was not worth having professionally refurbished. Used to seal some small tears in the cone, reglue detached spider to the frame, and (with some coffee filter as "stitching" material) to seal up the large incision made around the voice coil to access the spider. I wouldn't have attempted such a thing unless it was a last ditch effort with nothing to lose.Product is easy to apply, laying down a nice bead through the fine applicator tip. I love that the cap has a needle that inserts into the applicator tip to prevent clogs. For the more substantial patch-up work, I used a small hobby paint brush to apply over the coffee filter material. It was humid here at the time of application, and the glue was still just a bit tacky nearly 24 hours after application in the areas where it had been applied most liberally, so I gave it a little extra time. The product has only a minimal smell.I can't say yet if this fix is going to stand the test of time, but I can say that I now how have a useful speaker and radio instead of having to scour the forums for a spare out of someone's old junker. And this tube was a lot less expensive, and I have plenty left for my next repair. I couldn't be happier!

I had to reattach the outer rings to a couple of cheap Pyle speakers I was just testing for size. I was considering some pricier PVA adhesive from Simply Speakers but found this instead. The low mess applicator tip is built in to the tube and came in very handy. It seems to be doing the job, holding secure. I will be using this again.

Used this in a foam repair for my 2005 LEXUS GX470. The front foam had disintegrated and I bought this along with some replacements. I may have put too much glue in some areas but they dried nicely and it didn't matter because the speakers sounded great after!!

Only glue that you will need for speaker cone repairs. Very good quality quick setting and very strong holding ability. Highly recommend this product and seller. Low odor and any lingering smell will disappaite within a hour.

The edge of my 12” kicker subwoofer was split open in a few locations. From a few small 1” rips to a big 6” split along the outer rim across then about another inch along the inner rim. I used this product as instructed and the sub works as good as new. It’s held up for about 6 months now counting. Highly recommend

This is excellent speaker glue. I just got done refoaming 8 Vifa woofers with it and didn’t even use up one of the tubes of glue. It’s very easy to work with. The best part is that it has a thin metal needle nose tip to precisely dispense the glue, and the cap has a built in little poker that prevents glue from clogging the tip. It’s brilliant. And since you get two tubes of glue, it’s just a really incredible value as most speaker glue is overpriced. Make sure to apply glue to both sides if possible and give yourself anywhere from 2-5 minutes until you press them together. I used the glue on poly cones which are notoriously difficult to get glue to stick to and it works great. Very happy with purchase highly recommended.