Sight Tool with Heavy-Duty Construction and Rotatable Sight Prong, Sight Adjustment Tool Sight Removal Tool

Works as intended, only way to get S&W Bodyguard 2.0 sights to budge!

Very versatile. Works great well. Takes time to get the slide lined up straight but when it’s set, it works.

First off, I am not a gunsmith or armorer, so I have limited experience. However, consensus on the inter-webs is that M&P sights are notoriously difficult to remove and replace. I wanted to put night sights on a couple M&P pistols (9L 2.0 and Shield Plus) and to be able to refine their alignment if needed.Bottom line: This tool worked, and did not damage either the new sights or the old ones, which were removed. Rear sight took an uncomfortable amount of force to turn wheel, and resulted in a slightly tender thumb. However, for the price, versatility, and result, I would not hesitate to buy again. Seems sturdy based on heft, but I have not, and will not, use this extensively.M&P 2.0 9LAt first, I borrowed a friend's tool (not this tool). It worked for the rear sight, but would not work on the front sight of my M&P 9L 2.0 (5" barrel) because of the geometry of the slide and lack of a notch below the pushing block. Next, I used a brass punch and hammer to get the front sight out and new sight roughly in place. However, as you might expect, smashing something with a hammer lacked finesse and I was having trouble fine tuning the alignment of the new sight at home figured I would not have much luck at the range if I needed to do further adjustment. That's when I decided to give this tool a shot. Because the W Wiregear has that notch/cut-out below the pusher block, it worked perfectly to hold the long slide and nudge the front sight into alignment.M&P Shield PlusNext, I moved onto the Shield Plus. The front sight was relatively easy to remove and replace using the 90 degree side of the block. To hold the slide, there are 4 individual contact points that you screw down. I like that the tool has a series of lines etched in the surface that holds the slide. These lines allow you to make sure the slide is properly aligned (i.e. perpendicular to the pushing block), so you're applying force straight through the dovetail and not at an angle. However, I may have preferred the two-clamping-bar-style (like vise jaws) of my friend's tool in that (1) it did not require fiddling to get the slide aligned, and (2) did not create a pressure point on the thin material at ejection port. With the Shield, one of the pads/feet screwed down onto that thin section of the ejection port, when pushing the rear sight. I made it finger tight and did not try to really torque it down to reduce risk of future issues. Everything seems fine so far, but time will tell whether that area has been damaged or fatigued, and others may not be so lucky (e.g., because they use their ape strength and apply more force than I did). I reversed the pusher block to use the 45-ish degree side for the rear sight. The rear sight on the shield was DIFFICULT. The pusher block has large pushing surfaces, so there was no damage to the sights despite applying a lot of force. I found myself wishing for (1) a good surface to hold the tool while I cranked the wheel (I'd probably try putting the tool in a vise if I were doing it again), and (2) a larger wheel (or a nut that I could throw a wrench on to get more mechanical advantage). It worked, but my thumb was sore afterward from pushing so hard on the wheel's spindle.

I bought this during the Prime Days Sale. My only complaint is that one of the hold down nuts wobbled terribly on the support post. Upon examining it I noticed that the hole for the nut was drilled and threaded on an angle, in relation to the bearing surface of the nut, causing the nut to wobble 1/8' to 3/16", and applying uneven pressure to the top plate. I wrote to Amazon, and the manufacturer about this issue and requested a replacement nut. I haven't heard anything back from either of them, so I took the nut and mounted it on a mandrel in my lathe, and turned the bearing surface perpendicular to the bore of the nut. It's shorter now, but doesn't wobble , and applies even pressure to the top plate of the tool. That's just poor QC to let something that obvious to be shipped out for sale. A blind man could have seen the wobble in the nut. However, the price was about a third of others for sale at the time, and I think it will work just fine now.

Used on Springfield XDM 40. Sprayed both sights multiple times with PB Blaster for 48 hours before my attempt . Was worried the XDM slide was not square like the XD but covered in painter’s tape and clamped very tightly into the tool. Once properly installed in the tool, I began cranking. Hard!. Used leather gloves to protect my hands. Had it really torqued and the sights weren’t budging. At this point I put the tool in a vise, which fits nicely in a soft jaw vice. Per the instructions, I used a 3/8 punch and a 27oz. hammer to hit (hard} multiple times on the sight moving jaws on the tool in the direction of the removal. The last hit, the slide broke free and was able to be easily cranked out by the tool. XDM sights are tough to remove but don’t be shy to be aggressive. Protect the slide and go for it:. This tool is well built and can handle some serious torquing and smacking. I highly recommend it!

The sight press is made out of sturdy materials and has an okay fit and finish. It looks to be a quality product. However, none of that matters if it doesn’t work well.The first thing I noticed is the adjustable piece in the center cannot be turned unless you lift the top half of the press far enough up to make half turn adjustments. You should be able to adjust this piece without taking everything apart.The screws used to clamp the slide in place have a cheap stick on rubber pad to cover the steel clamp pads. After the first use, these get destroyed. In order to get enough pressure on the slide to keep it from twisting or moving forward you will squish the pads to the point of ruin. If you chose not to use the pads, the holding screws will ruin your slide finish.Due to the slip and movement in the press, it is impossible to make micro adjustments. By the time you get enough pressure on the sights to get it to move, the slop will overcompensate and spring the sight over… if that makes sense.I see some good reviews on this thing. So perhaps your mileage may vary. For me, this tool is a hard pass, especially for the money. There are much better options available.

Excellent sturdy product. Was able to effectively and accurately mount night sights to our pistols. Very pleased. Item was delivered within two days of ordering. Highly recommend

Maybe works for larger slides with bigger / looser sights, but this does not work with my M&P Shield (original). Too large, doesn't get a good grip on the rear sight, and the M&P's (at least mine) sight is way too snug for this to work. Didn't budge a hair, I ended up using a hammer and punch - which left the sight looking ugly. Will continue to look for something better to adjust my smaller carry sights.